Both cables run Gigabit Ethernet over the full 100 metres. The difference is 10 Gigabit: Cat6A carries 10 Gbps over the full 100 metres, while Cat6 carries it only over short runs, up to about 55 metres. Cat6A is thicker, costs more to buy and install, and needs more space in trays and racks. For most desks, Cat6 is enough; for Wi-Fi access points, server rooms, and buildings you expect to use for ten years or more, Cat6A is the safer choice.
The differences at a glance
| Cat6 | Cat6A | |
|---|---|---|
| Standard | ANSI/TIA-568.2-D Category 6, ISO/IEC 11801 Class E | ANSI/TIA-568.2-D Category 6A, ISO/IEC 11801 Class EA |
| Bandwidth | Up to 250 MHz | Up to 500 MHz |
| 1 Gbps | Up to 100 m | Up to 100 m |
| 2.5 and 5 Gbps | Up to 100 m | Up to 100 m |
| 10 Gbps | Up to about 55 m | Up to 100 m |
| Size | Thinner, easier to bend | Thicker and stiffer |
| PoE | Supported | Supported, with better heat handling in large bundles |
The 100 metres is the full channel: up to 90 metres of fixed cable in the wall or ceiling, plus up to 10 metres of patch cords at both ends.
Speed and distance
Both categories carry 1 Gbps, the speed most computers, phones, and printers use, over the full 100 metres.
The two categories differ at 10 Gbps. Cat6A was designed for 10GBASE-T and supports it to 100 metres. Cat6 can carry 10 Gbps only on shorter runs, up to about 55 metres, and only if interference from neighbouring cables (alien crosstalk) is low. In a busy ceiling with many cables bundled together, that is hard to guarantee.
Between the two sit 2.5 and 5 Gbps (the IEEE 802.3bz standard, also called multi-gigabit or NBASE-T). Both Cat6 and Cat6A carry these speeds over 100 metres. This matters because many modern Wi-Fi access points use 2.5 or 5 Gbps uplinks.
Wi-Fi access points
Wi-Fi 6E and Wi-Fi 7 access points can pass more than 1 Gbps of traffic, so they often have 2.5, 5, or 10 Gbps ports. Cat6 already supports 2.5 and 5 Gbps at full distance. Cat6A gives you room to move to 10 Gbps later without recabling the ceiling.
For new buildings, we usually recommend Cat6A to every access point, even when the desks use Cat6. Ceiling runs are the hardest to replace later. Read more in our guide to Wi-Fi 6, 6E, and Wi-Fi 7.
Power over Ethernet (PoE)
Both cables carry PoE for cameras, IP phones, access points, and access control readers. Higher-power PoE heats the cable, and a bundle of many powered cables gets warmer than a single one. Cat6A usually has thicker conductors, which handle that heat better, so it is the safer choice where you plan large bundles of high-power PoE devices.
Size, installation, and cost
Cat6A is noticeably thicker and stiffer than Cat6. That affects the whole installation:
- Cable trays, conduits, and ceiling routes fill up faster
- Patch panels and cable managers need more space
- Bends must be gentler, so pulling takes longer
- Cat6A jacks and panels cost more and take longer to terminate
The cable itself is only part of the cost. Labour, containment, and components add to the difference, so get quotes for both before deciding.
Shielded or unshielded
Both categories come as unshielded (U/UTP) and shielded cable, such as F/UTP or S/FTP. Shielded cable resists interference better but must be grounded properly from end to end, with shielded jacks and panels. Unshielded Cat6A is widely used for office cabling. Shielded cable is common in industrial sites or near heavy electrical equipment.
Use matching components
A link only performs to its category if every part matches: the cable, the jacks, the patch panel, and the patch cords. A Cat6A cable terminated on Cat6 jacks is a Cat6 link. Mixing brands can also cause problems, so use one manufacturer's system where possible.
Test and certify every link
You only know a link meets its category once it has been tested. A cable certification tester measures each link against the standard and gives a pass or fail result with the details. Ask your installer for the test report for every link, along with the labels and as-built drawings. Without them, you have no proof the cabling performs as promised.
What about Cat5e, Cat7, and Cat8?
- Cat5e carries 1 Gbps to 100 metres and 2.5 Gbps under 802.3bz, but it is no longer a good choice for new installations.
- Cat7 is not a TIA category. It exists in the ISO/IEC standard as Class F and uses its own connectors, so you rarely see it in real office installations.
- Cat8 is for short links of up to 30 metres inside data centres, at 25 or 40 Gbps. It is not used for office cabling.
Which should you choose?
- Desks and printers: Cat6 is enough for most offices.
- Wi-Fi access points: Cat6A, so you can move to 10 Gbps later.
- Server rooms and short links between switches: Cat6A for copper, or fiber for longer links.
- New buildings you will keep for ten years or more: Cat6A everywhere is the safest choice.
- Adding points to an existing network: match what is already installed, unless you are upgrading.
Arab Spec designs, installs, tests, and documents structured cabling across Saudi Arabia, and the network that runs on it.
Frequently asked questions
Is Cat6A faster than Cat6?
Both carry 1, 2.5, and 5 Gbps over the full 100 metres. Cat6A carries 10 Gbps over the full 100 metres, while Cat6 carries 10 Gbps only on shorter runs, up to about 55 metres.
Can Cat6 run 10 Gbps?
Yes, on shorter runs of up to about 55 metres, and only where interference from neighbouring cables is low. For 10 Gbps over longer runs, use Cat6A.
What is the maximum length of a Cat6 or Cat6A cable?
100 metres for the full channel: up to 90 metres of fixed cable plus up to 10 metres of patch cords in total.
Do we need Cat6A for Wi-Fi 7?
Not always. Cat6 carries 2.5 and 5 Gbps to 100 metres, which suits many Wi-Fi 7 access points today. Cat6A lets you move them to 10 Gbps later without recabling, so it is the safer choice for new buildings.
Can we use Cat6A patch cords on a Cat6 network?
Yes, they work, but the link still performs as Cat6. Every part of a link must be Cat6A for it to perform as Cat6A.
Is shielded cable better?
Shielded cable resists interference better, but it must be grounded properly with shielded components throughout. In a normal office, unshielded cable performs well. Shielded cable suits industrial sites and areas with heavy electrical equipment.
How do we know our cabling meets its category?
Ask for a certification test report for every link. A cable certification tester checks each link against the standard and records whether it passes.
